Program with sub program wont run

[ads]

Has this simple program running on mach , now it doesnt want to run on the new controller



It gives an error



here it is

N0000
N0010
N0020 M98 P1234 L22
N0021 M05
N0025 M30

O1234
N0030 G20 (Units: Inches)
N0040 G40 G90
N0050 F1
N0080 (.250 Mill/Drill)
N0090 T2 M06 G43 H2
N0100 M03 S2000
N0110 G00 X0.5
N0111 G01 Z-0.5 F25
N0120 G00 Z 0.250
N0130 G00 A180
N0140 G01 Z-0.5 F25
N0141 G00 Z 0.250
N0142 G00 X1.5
N0151 G01 Z-0.5 F25
N0152 G00 Z 0.250
N0153 G00 A0
N0154 G01 Z-0.5 F25
N0155 G00 Z 0.025
N0156 G00 X2.5
N0157 G01 Z-0.5 F25
N0159 G00 Z 0.250
N0160 G00 A180
N0161 G01 Z-0.5 F25
N0162 G00 Z 0.250
N0163 G00 X3.108
N0164
N0165 G92 A0
N0166 G92 X0
N0167 M99



any thoughts

 

[masso-support]

try removing G40 in N0040 as it's not required, unsupported gcodes will cause issues.

 

[jolbas]

You need to put the sub program in a separate file called 1234.nc The line with O1234 isn't necessary.

https://www.masso.com.au/masso-documentation/?section=m98-m99-sub-program-call

 

[ads]

still having issues with this sub program

attached are the 2 files



any help would be great

N010 M98 P10 L22



N0030 G20 (Units: Inches)
N0040 G90
N0050 F1
N0090 T2 M06 G43 H2
N0100 M03 S2000
N0110 G00 X0.5
N0111 G01 Z-0.5 F25
N0120 G00 Z 0.250
N0130 G00 A180
N0140 G01 Z-0.5 F25
N0141 G00 Z 0.250
N0142 G00 X1.5
N0151 G01 Z-0.5 F25
N0152 G00 Z 0.250
N0153 G00 A0
N0154 G01 Z-0.5 F25
N0155 G00 Z 0.025
N0156 G00 X2.5
N0157 G01 Z-0.5 F25
N0159 G00 Z 0.250
N0160 G00 A180
N0161 G01 Z-0.5 F25
N0162 G00 Z 0.250
N0163 G00 X3.108
N0165 G92 A0
N0166 G92 X0

 

[jolbas]

You need to end the subprogram file with M99

Line N0050 doesn t seem to do anything. Better to remove.

Did you name the file with subprogram 10.nc ?

 

[ads]

yes but it still doesnt work



my files seem to save as .nc.txt is that ok?

 

[jolbas]

No. You have to remove .txt from the end of the file name.

 

[ads]

That did it thanks!